Plated Mortise

Plated Mortise

What Distinguishes a Quality Wooden Poker Chip Case from a Basic Box?

So you have decided to invest in a poker chip case to store all of your poker chips. There are a multitude of chip cases and trays on the market, from inexpensive plastic trays to outrageously expensive sets. If you have your heart set on a wooden poker chest, here are some things to consider that differentiate a fine poker chip case from just a plain wooden box.

 JOINTS

Joinery is a part of woodworking that involves joining together pieces of wood, to create furniture, structures, toys, and other items. The characteristics of wooden joints - strength, flexibility, toughness, etc. - derive from the properties of the joining materials and from how they are used in the joints. Therefore, different joinery techniques are used to meet differing requirements. When designing a poker chip case, you have to take into account the weight of the chips, which can approach 50 lbs for a 1000 chip case. The joints have to be strong, or the case will fall apart under the weight of the chips.

Most pre-made cases bought on the market utilize a butt joint. A butt joint is a joinery technique in which two members are joined by simply butting them together. The butt joint is the simplest joint to make since it merely involves cutting the members to the appropriate length and butting them together. It is also the weakest because unless some form of reinforcement is used, it relies upon glue alone to hold it together. Because the orientation of the members usually present only end grain to long grain gluing surface, the resulting joint is inherently weak.

When ordering a custom chip case, you can specify a dovetail joint. A dovetail joint is a joint technique most commonly used in woodworking joinery. Noted for its resistance to being pulled apart (tensile strength), the dovetail joint is commonly used to join the sides of a drawer to the front. A series of pins cut to extend from the end of one board interlock with a series of tails cut into the end of another board. The pins and tails have a trapezoidal shape. Once glued, a wooden dovetail joint requires no mechanical fasteners.

Another simple and strong joint is the mortise and tenon joint, which has been used for thousands of years by woodworkers around the world to join pieces of wood. This is commonly used when the pieces are at an angle close to 90°. Although there are many variations on the theme, the basic idea is that the end of one of the members is inserted into a hole cut in the other member. The end of the first member is called the tenon, and it is usually narrowed with respect to the rest of the piece. The hole in the second member is called the mortise. The joint may be glued, pinned, or wedged to lock it in place.

HARDWARE

Hardware for a poker chip case must also be durable. A variety of hinges and hardware are used in commercial cases, but usually a stamped hinge is used which is the weakest type of hinge. When ordering a custom case, there are a variety of hinges you may request.

A full length piano hinge is a long narrow hinge that runs the full length of the two surfaces to which its leaves are joined. This imparts additional strength to the hinge when a solid wood lid is used.

Concealed Hinges are used for furniture doors (with or without self-closing feature, and with or without dampening systems). They are made of 2 parts: One part is the hinge cup and the arm; the other part is the mounting plate. Also Euro/cup hinge. This gives a cleaner look to the case.

FINISH

One thing to consider when choosing a wooden chip case is to specify that the finish be ‘chip friendly.’  Polyurethane or a non-soluble varnish is an ideal choice, as it does not stain or seep into your chips.  Specifically, avoid any type of Oil finish such as Tung or Danish oil, as these oils can penetrate into the clay chips over time.

CHIP SIZE

Commercial chip trays are usually 'one-size-fits-all', so be certain that your chips are appropriately sized for the chip case.  If ordering a custom chip case, be sure to specify the size of your chips. The majority of chips are of the 39mm size.  However, large denomination chips, as well as chips based on the Paulson Inverted Hat and Cane (IHC) fractionals mold, are a larger 43mm size. Casino Chip thickness can also impact how difficult it is too add or remove chips from a tray.  As a chip begins to show signs of wear, edges may become less crisp and the chip becomes a bit thinner.  Over time, chips may begin to wiggle a bit in the case.

So when investing in a wooden poker chip case to store your chips, remember to consider the type of joints, hinges, and finish used in the design of you case.

About the Author

Sven Asnien is an experienced woodworker and craftsman with tremendously varied experience. Born and raised in Cleveland, Ohio, he began his woodworking career at Wooster College with theatrical carpentry, building sets and props for the and a traveling theatrical group. He continued to perfect his woodworking skills after college, working primarily on built-in cabinetry, wainscoting, and high-end finish carpentry.

Sven establish Oz Woodworking to combine his love of woodworking and poker. For more information about custom wooden poker chip cases and trays, visit www.ozwoodworking.com or e-mail us at sven@ozwoodworking.com.

How can I remove the knobs on a mortise lockset?

It is a Corbin knob mortise set with a cylinder to retract the latch on one side and the two push buttons on the mortise box plate to lock/unlock the knob. My issue is I want to re-swing the door so I need to reverse the latch. I have easily taken out the cylinder, but I don't know how to take the knobs off to pull the mortise box out of the door. There are no set screws or slots in the knob at all. It is very old Corbin commercial hardware. I really want to reuse this door to hang in my house, but I need to reverse the latch. How do I remove the knobs?
I can take the 4 screws off of the face plates on each side, but this doesn't do anything either. There definitely isn't any set screws or slots on the knobs anywhere. It is from the early 1900's.

Without actually seeing the lock I can only guess but did you try to take the plates off the door? Although most knobs have a screw that when removed you can pull the knobs off there is also another lesser used method where the knob is attached to the plate on either side of the door. once the plate on one side is removed the shaft connecting the 2 knobs can be removed as well as the plate on the other side. The knobs and the plates come off as 1 piece. Hope this helps.

Good Luck!

Fitting a Router Table Insert Plate - Routing Big Mortises